While we are no longer making active post of Cricut projects on this blog as of 8/1/2013, we invite you to use it for continued die cut inspiration as we will leave the blog up for viewing. Happy Cricuting !

Friday, September 7, 2012

Flower Bead Spray Made From Soda Cans

Hello everyone, it's Melody (aka KauaiMelody) and you can visit me at http://cricutmelody.blogspot.com/.  I am so happy you stopped by for some inspiration to fuel your creative mojos.  The project I would like to share with you today is a Flower Bead Spray made from soda cans.  I placed the spray on a wrapped gift for a friend.  Don't you think it adds a special touch and gives it an extra punch?


Now here is the list of supplies you will need.

Cricut Info & Supplies Used:
Designed by: Melody
Cricut Machines Used: Cuttlebug
Cricut Cartridges Used: n/a
Other Supplies Used:  Provocraft Floral Dies, prepared soda cans, 26 gauge silver wire, crystal beads, clear gems, pearls, Stickles, Glossy Accents, Glue Gun, sharp instrument or small hole puncher for flower centers.

Let's get started by preparing the soda cans. . .

Soda Can Preparation: (For added safety, you can wear goggles andrubber gloves)

1.  Rinse out soda can and shake out.
2.  Poke starting cut with exacto knife, along top side and bottom.
3.  Cut aluminum around circumferences, using starting cut, at top and bottom with scissors.
4.  With scissors, trim off raggedy edges, and cut rectangle to the size you want.
5.  Rinse any sticky stuff and dry.
6.  You can further smooth edges with sandpaper or an emery board.
7.  Now use the aluminum as you would paper in your Cuttlebug.

Next, you will need your Cuttlebug, Provocraft Floral Diecut Set, and your prepared aluminum.

Cuttlebug "Sandwich" (starting from the bottom)
Plate A
Plate B
Diecut blades up
aluminum
Plate B

Cut 3 small flowers, 3 medium and 3 large

You will need 26 gauge silver wire.  Measure an arms length and fold in half.
You have now made your first loop for your spray. Now slide a bead towards the end of the loop.
When you get to the end of the loop, twist the bead and wire until you have the length you like.
It is as easy as 1 2 3, Loop, Slide and Twist.  Now repeat these three steps, making two more loops.
Continue until you have made a spray with 3 beads. Congratulations - they look beautiful!
Now make a new spray with 3 pearls, just like you made your first one.
Your third spray will be made with the 3 small soda can flowers, making center holes first.
And finally, make your fourth spray, layering the middle and large flowers,making center holes first.
You now have 4 beautiful sprays, and it is time to twist them all together at the base.
When all four are twisted you can adjust the "branches" and place it on your package.
Remember to admire your Flower Bead Spray, before you give it away.
And one last time  for kicks and giggles.


Tips:

After making the center hole, I like to cut a slit up to the hole (but not too close) so the wire twists neatly close to the center.

When you glue a gem to the center, make sure you leave a tiny space for the wire to pass through.

Remember you can make these uniquely yours (stickle, emboss, alcohol ink etc. to your liking).

Questions???
If you have any questions, leave them in the comment section, and I will answer them for you.

Thank you so much for stopping by the Cricut FANatics Blog, one of my favorite places to chill and get inspired.  I look forward to designing and sharing more projects with you again.  

Joyful Crafting  Always,
Melody  

47 comments:

  1. Thank you, Melody for an inspiring project with great instructions! Love your re-use of the soda can and wire to create such a sparkly spray!

    ReplyDelete
  2. This is lovely and a wonderful way to spruce up a gift.

    ReplyDelete
  3. Wow, great project. Thanks for the tut--you made it look so easy :-) I need to try this!

    ReplyDelete
  4. I certainly hope these are part of the Flower Spray swap from the circle....I definitely want one of these!!! Thanks for the inspiration, I can't wait to get started on mine.

    ReplyDelete
  5. WOW! Love it!! Thanks for sharing this idea!!

    Julie

    ReplyDelete
  6. Thank you for sharing this great idea!!!
    Julie

    ReplyDelete
  7. Love that you used recycled cans! Your project is beautiful!!

    ReplyDelete
  8. Very very cool. Love the idea what a fantastic idea. Very pretty flowers.

    ReplyDelete
  9. oh Melody....this is just the coolest project ever ! I can see making this for a special wedding gift wrapping I am doing for step sister later this year ! So inspiring and with your great step by step directions I think even I can handle this ! Thanks for sharing !

    ReplyDelete
  10. Melody, your project is totally cool!! Thank You!!

    ReplyDelete
  11. Thank you so much for sharing your creation with us! Great instructions too!

    ReplyDelete
  12. WOW Melody great project today! This really helps because I am in a floral spray swap right now and my wire seems to get so thick when I wrap it. I don't know how to make it thinner. Thanks for the tutorial

    ReplyDelete
  13. This is clever and beautiful! Great post and beautiful project!!!

    ReplyDelete
  14. This would be great for some wonderful Christmas sprays! Beautiful!!

    ReplyDelete
  15. Love love love this. It is so pretty. Thanks for sharing your bead instructions. I may have to try this.

    ReplyDelete
  16. The aluminum flowers were really amazing! Thanks so much for the clear instructions I may just have to try it sometime!

    Donna

    ReplyDelete
  17. Hello everyone, thank you for all the craft love and glad you are enjoying the soda can flower bead spray. Promise you'll try this. Once you do, you won't be able start. You will receive lots of compliments from the recipients of these, and you will just plain have fun making them for YOU.
    Joyful Crafting Always
    Designer and Cricut FANatics Blog Supporter, Melody

    ReplyDelete
  18. GORGEOUS!!!! ABSOLUTELY GORGEOUS!! You are so amazingly creative!! TFS!!!

    ReplyDelete
  19. What a great project. I'm a HUGE fan of recycling, and when you can incorporate it into crafting, I'm on board! It's beautiful, thrifty and something I can see myself making over and over. Thanks for sharing!

    ReplyDelete
  20. Wow Melody! You know how much I love your soda can flowers and now a bead spray! Your creativity is inspiring! Your tutorial is awesome too. I will have to try these soon.

    ReplyDelete
  21. That spray is so beautiful!! I might just have to try making one. Are the flower edges sharp? I'm just wondering if the recipient of the gift could get cut or can the edges be sanded or something.

    ReplyDelete
  22. Stunning floral spray! Thank you for the great tutorial! I added this to my project to do list. Congrats on your debut!
    Michelle

    ReplyDelete
  23. This is absolutely gorgeous! I need to find some soda drinkers so I can play!

    ReplyDelete
  24. SHERRI B/ANSWER
    REPLY BUTTON ISN'T WORKING, SO I WILL ANSWER HERE AND HOPE YOU CHECK BACK , OR I CAN TRACK YOU DOWN IN ANOTHER VENUE.
    The edges are very manageable and can be filed down with an ordinary emery board. It just takes a few seconds to do this if you have concerns. Designer/KM

    ReplyDelete
  25. SCRAPPERBECK/ANSWER

    Sometimes when you twist the wires at the base, it clumps up in one spot, so try to distribute the twist down the whole length, not just one spot. When I have a thick spot, I unwrap if possible and try again, or decide to wrap just the base in a floral tape and add a bow. This is actually attractive as well. For example, add black floral tape for a dramatic look, with some matching beads in the spray. Designer/KM

    ReplyDelete
  26. Hi!
    Absolutely beautiful, I've never done work with soda cans, I will give this a try, thanks

    ReplyDelete
  27. This is really cool! Thanks for sharing with all of the steps too!

    ReplyDelete
  28. Absolutely fabulous Melody! Another project on my bucket list! Thank you for the great instructions too!

    ReplyDelete
  29. Wow! thats awesome!! TFS the instructions too!

    ReplyDelete
  30. I've always wanted to make one of these,now I can thanks to you providing the instructions. :) It is simply beautiful,Melody! :)

    ReplyDelete
  31. Melody, this is so beautiful! You give such wonderful instructions that I feel like I like I can actually do this! Who kew soda cans could be so beautiful??

    ReplyDelete
  32. What a great idea! You have done a beautiful job and your directions have great detail...thank you!

    ReplyDelete
  33. TFS Melody. I can't wait to try this. :) Christine

    ReplyDelete
  34. Love your floral spray, it's so beautiful!

    ReplyDelete
  35. Very nice spray! Every time I see these done I think I'll attempt them.

    ReplyDelete
  36. Thanks for the detailed instructions, gonna try it!

    ReplyDelete
  37. These are amazing!! I am so afraid of cutting myself though, lol. I will just admire yours from afar! :)

    ReplyDelete
  38. I've seen other things made from soda cans and I've wondered about how it was done. Thanks for the tutorial. Beautiful.

    ReplyDelete
  39. Your spray is beautiful! I really appreciate the tutorial and pics!

    ReplyDelete
  40. You can also texture flowers by running through the cuttlebug.

    ReplyDelete
  41. Thanks for sharing! It looks so easy now.

    ReplyDelete
  42. those are very nice. thanks for sharing how to make them.

    ReplyDelete

Please leave a kind word for our Cricut FANatic Designers to let them know you stopped by and appreciate their work.